Oculus Quest 2 settings for Microsoft Flight Simulator 2020

The current state of PC based VR in 2021 ranges from:

  • OMG this is incredible, it’s so immersive it feels like you’re really there!

to

  • The low FPS is terrible, stuttering and motion tracking lag, ugh this is making me seasick

I just got an Oculus Quest 2 to use with Microsoft Flight Simulator with the Link cable. I was surprised that out of the box it’s actually a terrible experience with MSFS, horrible framerate (< 10fps), and jerky, laggy head tracking. I could only handle it for about 5 mins before taking it off. My initial reaction was that I was disappointed. I know from reading online though that plenty of people are using a Quest 2 over Link successfully and are pleased with the results, so some searching around found a number of threads recommending optimal settings.

tldr; if you’re prepared to spend time tweaking driver and and app settings, the Quest 2 with MSFS really is an incredible experience, and for the low cost (compared to something like the G2 Reverb), I’d definitely recommend it. To get it running smoothly though, you need to make a number of updates and config changes in a number of different places:

  • Disable any onscreen display overlay type apps, e.g. in onscreen display in Ndivida settings and disable the Window 10 Game bar. There seems to be a known issue with onscreen display apps that either the Quest, the Link drivers, or MSFS cannot handle correctly right now, resulting in the display in the headset flickering back and forth between MSFS and the Oculus Home app
  • Update the Oculus software to Beta and accept the updates to run latest beta versions
  • ymmv but for me the SteamVR approach was much less smooth than the Oculus OpenXR software. Try both and see what works best for you. Others reported the SteamVR software was smoother for them

Here’s my specs for comparison (specific details here):

Asus X570 mobo

Ryzen 5 3600XT

32GB DDR4 RAM

Corsair MP600 m2 NVMe SSD PCIe Gen4

RTX 2060

There are a couple of useful threads where you can find the majority of these tuning tips, these 2 specifically:

https://forums.flightsimulator.com/t/quest-2-2080ti-link-fs2020-set-in-ultra-best-performance-simple-setup-guide/346291

and

https://forums.flightsimulator.com/t/my-2070-super-vr-settings-and-suggestions-index-steamvr/321913

For the majority of my settings I followed these exactly and tweaked slightly to get the smoothest settings I was comfortable. Here’s screenshots of the relevant parts:

Nvidia control panel:

Oculus app: 90hz and 1.3 was recommended in one of the threads, but I went with 80hz and 1.0 that I found was much smoother:

Oculus Tray App – start as Administrator and leave running when you run MSFS:

0.8,0.8 FOV had a significant improvement to the framerate. Any smaller than this, like 0.7,0.7 and I could noticably see the reduced field of view in the headset.

Link settings:

I’m not sure how much difference these settings made. I played around with the Bitrate for example between 250 and 500 and didn’t notice any improvement to the quality or the framerate.

For me, the combination of all the above settings with my hardware resulted in very playable and smooth output in the headset. I don’t think the graphics are as sharp as they could be, but I’d rather have smooth and less sharp than super sharp and detailed but juddering around when I move my head.

I was very surprised that the Quest 2 does not produce good results with MSFS and the link cable out of the box, but following some of the recommendations you find in the linked forums threads should get you good results.

3 Replies to “Oculus Quest 2 settings for Microsoft Flight Simulator 2020”

  1. Hi Kevin, i have seen your interesting blog.You are my last hope to get my brand new Quest2 with FS2020 running. On the desktop the Flusi runs wonderfully, but when switching to VR (in the menu or with Ctrl/Tab) the error message “Headset not found” always comes up. I installed the Oculus software, connected cable correctly, cable test shows 2.4 Gbps. Open_XR driver is in the correct Oculus directory “Computer\HKEY_LOCAL_MACHINE\SOFTWARE\Khronos\OpenXR\1”. With Virtual Desktop Streamer I can start the Flusi and see the desktop in the Quest2, but as soon as I want to switch to VR always comes the same error message. It’s exasperating || , I’ve been struggling for days to find a solution and haven’t found anything. Please for your help for a VR beginner. Thanks a lot. 🙂 Greetings from Tulln/Austria from Ron

Leave a Reply to Ronald Stubbings Cancel reply

Your email address will not be published. Required fields are marked *

This site uses Akismet to reduce spam. Learn how your comment data is processed.