After going through all the setup options but before it gets to starting the actual install on an ESXi VM I get the error:
“ERROR: The disc you inserted is not a Solaris OS CD/DVD”
From this post here about the same error on a Dell server (I’m installing on a VM on an HP DL380 G7) with Solaris driver issues with ATAPI CD/DVD devices, I changed the virtual CD drive on my VM from SATA to IDE, and can now get past the error.
This should be filed under “Can you? Yes. Should you? Probably not”
I tried creating a Docker container running Oracle 19c from Oracle official dockerfiles, and straight out of the gate ran out of diskspace:
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! checkSpace.sh: ERROR - There is not enough space available in the docker container. checkSpace.sh: The container needs at least 18 GB, but only 14 GB are available. !!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!! Removing intermediate container b53a5e13a45c The command '/bin/sh -c chmod ug+x $INSTALL_DIR/*.sh && sync && $INSTALL_DIR/$CHECK_SPACE_FILE && $INSTALL_DIR/$SETUP_LINUX_FILE && rm -rf $INSTALL_DIR' returned a non-zero code: 1
ERROR: Oracle Database Docker Image was NOT successfully created. ERROR: Check the output and correct any reported problems with the docker build operation.
This is part 3 of 3 in a series on adding new drives and storage to my HP DL380 G7 server and ESXi. The previous 2 parts are here, part 1 – adding new drives, and part 2 – configuring a new RAID array.
After the previous two steps were complete, the new disks are in, the new RAID array configured, the next step is to add the storage in ESXi to be available to new VMs. Here’s my starting point, almost out of space:
Right now I have 1 Datastore configured in ESXi:
To add a new Datastore in ESXi:
At this point I ran into the error ‘Failed to create VMFS datastore’:
This post with steps to fix the partition table on the newly added drives. First step was to enable the sshd service to ssh into the server:
First, use this command to find the disk id of the newly added disk. Here I can see my new disk array as it’s the one closest to 1TB, the size of the new disks:
ls -lha /vmfs/devices/disks/
This command shows the issue with the partition table on the new disk array:
partedUtil getptbl /vmfs/devices/disks/(disk ID)
Next, use this command to reset the partition table to msdos type for the new disk array:
A while back I added my first disks to my $150 eBay HP DL380 G7 server – if you’re looking for steps on how to get to the RAID settings on the DL380 server, see my previous post here.
I recently started to run out of space on the 2 drives I’d installed previously, so time to add some more storage. I added a couple of cheap refurbished WD Blue drives described here, and I have a step by step post on physically installing the drives here.
Now the drives are installed, I need to add them to the RAID controller. After the POST tests, hit F8 to get to the iLO setup, and then exit, per the steps described in my earlier post here.
Press F8 when prompted to get to the RAID setup:
Select ‘Create a Logical Drive’ – here I’m adding a new RAID array with my 2 newly inserted drives:
I selected the 2 newly installed 1TB drives, in a RAID 1+0 config:
F8 to save:
Saved:
… and now I have 2 RAID arrays, the first one I added at a 750GB RAID 1+0 array, and now the new 1TB RAID 1+0 array:
In the next post I’ll show adding a new store in ESXi to use the new space on this new RAID array.